Re: 2009 Porsche Boxster S
A customer got in contact about a recent purchase of a Porsche Boxster S finished in ………. Black
The car came into us,
we carried out a full inspection of the exterior of the vehicle before taking the keys of the customer,
This is an extremely good example of a Porsche Boxster S with around 50,000 miles on the clock, on a 2009 registration, finished with black leather and a manual gearbox this is a real drivers car, the owner had expressed that he wanted to bring the car up to a good level but he was still going to use the car for trips overseas in his ownership, which was a great practical approach
What work we did
the car then went through a full decontamination process, this is a deep clean wash.
After the pre-wash, a conventional three-bucket wash was carried out, followed by a very thorough decontamination. First, the tar was removed using Insta Finish – an LA-based brand owned by the long-established Warner Chemical Manufacturing. The fallout was next on agenda with CarPro IronX on the wheels to work their magic.
Finally, the Bilt Hamber Auto-Clay Clay Bars
clay bar was put to good use removing any remaining bonded contaminants.
The vehicle was in for convertible hood deep clean and treatment as well as machine and ceramic coating work, as part of the safe wash stage the convertible hood went through full extensive decontamination, essentially a lot of all-purpose cleaners and elbow grease with a variety of brushes, to get out the contaminants and greenery filter in the fabric
After another safe wash it was finally time to Bring the car in dry off and inspect under the light, paint depth gauges were carried out around the vehicles paintwork to identify light spots, where the pain is thin
Once the pain sickness gauges have been carried out, we identified that the bonnet was particularly thin, my assumption is that this would’ve been an original bonnet due to a few stone chips, the rest of the paintwork was extremely clean and free from car park dinks and marks and knocks, although the paintwork was a severely swollen defect from poor washing.
At this point a conversation with the client to discuss whether a full correction was on the cards,
Wanted to go down a two-stage machine polish route rather than a full correction on the paint correction side of things
The bodywork was covered with film so that the convertible hood could be coated, the following morning the second layer of Gtechinq Fabric coat was applied, and after curing time for the roof to dry off, the convertible hood and all the glass were taped up ready for machine polishing stage to start.
The machine polishing process, the first was using a cutting pad and polishing using the
Rupes Bigfoot LHR15 Mark 2 machine doing the majority of the work,
Photo before and after
Then a finishing pad and fining compound for refinements and moving those lighter scratches making the metallic sparkle and boosting the glass levels super soft white pad with the corresponding Diamond ultra fine polish
and finally, the iBrid Nano takes care of the smaller areas around the window frame with more intricate crevices.
will use a vast array of different machines, pads, and compounds – often mismatching brands for their desired effect.
This leads to an immeasurable number of possible combinations, and regardless of the paint you are confronted with, the chances are there will be a configuration that will do the trick. Just to add to the potential complexity, you can also adjust your method – varying the number of passes per set for example –
and add in extra elements of the front and rear bumper that have been re-sprayed and there was overspray up the front two arches and the rear quarter panels.
That said, Rupes are unique in that they manufacture their own machines, compounds, and pads – and they are developed together to provide what they refer to as a ‘system’.
In the past, we have attended Rupes Advanced Bigfoot Technique Seminar where he was honing his skills under the tutelage of Jason Rose, Global Director of Training for Rupes, who we interviewed later that day for the Car Care Adventures.
Before going any further, we got out the Scangrip LED swirl-spotting equipment and the panel wipe the check the results of the machine polishing stage of the detail
final check before ceramic coating
after panelling the bodywork to remove any fillers and oils that have been left by the machine polishing stage
I finally inspection of the vehicle paintwork after the car has been panelled white to identify the true state of the paintwork, once we were happy we can then proceed with the ceramic coating
Once satisfied that the job was done properly, we set to work coating the car with Gtechinq Crystal Serum Light we applied this late on the evening of the second day of the booking so that there was a solid 12+ hours for this to bond to the vehicles paintwork,
The crystal serum light ceramic coating is more of a hard-core product that bonds to the vehicle’s paintwork think of this as an additional clear coat, it is this side of the product that offers more durability and more prevention of swell marks on the paintwork.
The next day we came in early and applied to the first coat of gtechniq EXO V4 the manufacturers say that there is a curing time of two hours, as a matter of course we let this cure for four hours to get the ultimate bond between layers, an additional layer went on after lunchtime, the glass levels were really starting to show now,
The combination of these two products with the correct curing time between layers will offer the ultimate protection to your vehicles paintwork with a hardy base coat (to help prevent swirl marks in the paint) that is bonded to the paintwork, and two layers of top coat for a finish which offers the ultimate in gloss, hydrophobicity and a superior finish
The Porsche wheels were deep cleaned with a panel wipe to remove any surface contaminants and dust then coated with Gtechinq C5 Alloy wheel armour ceramic coating applied to the wheel faces, this helps prevent brake dust buildup on the wheel and ease of cleaning
The exterior glass had three coats of Gtechinq G1 ClearVision, this is to help visibility when driving in rainy conditions really helps hydrophobicity on the glass.
The interior was hoovered and cleaned throughout, including the boot and under the hood, leather and all the carpets were coated and treated with Gtechinq L1 Leather Guard treatment and protection
Gtechniq I1 Fabric Carpet treatment and protection
Day 5 Hand over
On day fifth day the car was ready to be handed back to a very happy client.
Thanks for reading